# # OpenEmbedded local configuration file (sample) # # Please visit the Wiki at http://openembedded.org/ for more info. # # # Be SURE to read this file in its entirety and the GettingStarted page on the # wiki before proceeding. # # Once you have done that, remove the line at the end of this # file and build away. # # WARNING: lines starting with a space (' ') will result in parse failures. # Remove '# ' from commented lines to activate them. # # NOTE: Do NOT use $HOME in your paths, BitBake does NOT expand ~ for you. If you # must have paths relative to your homedir use ${HOME} (note the {}'s there # you MUST have them for the variable expansion to be done by BitBake). Your # paths should all be absolute paths (They should all start with a / after # expansion. Stuff like starting with ${HOME} or ${TOPDIR} is ok). # Use this to specify where BitBake should place the downloaded sources into DL_DIR = "${HOME}/sources" # Delete the line below. Then specify which .bb files to consider for # your build. Typically this will be something like BBFILES = "/path/to/openembedded/packages/*/*.bb" BBFILES := "${@bb.fatal('Edit your conf/local.conf: BBFILES')}" # Use the BBMASK below to instruct BitBake to _NOT_ consider some .bb files # This is a regulary expression, so be sure to get your parenthesis balanced. BBMASK = "" # Uncomment this if you want to use a prebuilt toolchain. You will need to # provide packages for toolchain and additional libraries yourself. You also # have to set PATH in your environment to make sure BitBake finds additional binaries. # Note: You will definitely need to say: # ASSUME_PROVIDED = "virtual/arm-linux-gcc-2.95" # to build any of two Linux 2.4 Embedix kernels, # i.e. openzaurus-sa-2.4.18 and openzaurus-pxa-2.4.18 - and don't forget # to rename the binaries as instructed in the Wiki. # ASSUME_PROVIDED = "virtual/${TARGET_PREFIX}gcc virtual/libc" # Select between multiple alternative providers, if more than one is eligible. PREFERRED_PROVIDERS = "virtual/qte:qte virtual/libqpe:libqpe-opie" PREFERRED_PROVIDERS += " virtual/libsdl:libsdl-qpe" PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}gcc-initial:gcc-cross-initial" PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}gcc:gcc-cross" PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}g++:gcc-cross" # Uncomment this to specify where BitBake should create its temporary files. # Note that a full build of everything in OpenEmbedded will take GigaBytes of hard # disk space, so make sure to free enough space. The default TMPDIR is # /tmp # Don't use symlinks in in the path to avoid problems # TMPDIR = /usr/local/projects/oetmp # Uncomment this to specify a machine to build for. See the conf directory # for machines currently known to OpenEmbedded. # MACHINE = "collie" # Use this to specify the target architecture. Note that this is only # needed when building for a machine not known to OpenEmbedded. Better use # the MACHINE attribute (see above) # TARGET_ARCH = "arm" # Use this to specify the target operating system. The default is "linux", # for a normal linux system with glibc. Set this to "linux-uclibc" if you want # to build a uclibc based system. # TARGET_OS = "linux" # TARGET_OS = "linux-uclibc" # Uncomment this to select a distribution policy. See the conf directory # for distributions currently known to OpenEmbedded. # Stay away from unversioned distros unless you really know what you are doing # DISTRO = "familiar-0.8.3" # Uncomment this to select a particular kernel version if supported by # your MACHINE setting. Currently only supported on Zaurus Clamshells. # KERNEL_VERSION = "2.6" # Uncomment one of these to build packages during the build process. # This is done automatically if you set DISTRO (see above) # INHERIT = "package_ipk" # INHERIT = "package_tar" # Add the required image file system types below. Valid are jffs2, tar, cramfs and ext2 IMAGE_FSTYPES = "jffs2 tar" # Uncomment this to disable the parse cache (not recommended). # CACHE = "" # Uncomment this if you want BitBake to emit debugging output # BBDEBUG = "yes" # Uncomment these two if you want BitBake to build images useful for debugging. # Note that INHIBIT_PACKAGE_STRIP needs a package format to be defined # DEBUG_BUILD = "1" # INHIBIT_PACKAGE_STRIP = "1" # Uncomment these to build a package such that you can use gprof to profile it. # NOTE: This will only work with 'linux' targets, not # 'linux-uclibc', as uClibc doesn't provide the necessary # object files. Also, don't build glibc itself with these # flags, or it'll fail to build. # # PROFILE_OPTIMIZATION = "-pg" # SELECTED_OPTIMIZATION = "${PROFILE_OPTIMIZATION}" # LDFLAGS =+ "-pg" # Uncomment this to enable parallel make. # This allows make to spawn mutliple processes to take advantage of multiple # processors. Useful on SMP machines. This may break some packages - we're # in the process of marking these so let us know if you find any. # PARALLEL_MAKE = "-j 4" # Uncomment this if you want BitBake to emit the log if a build fails. BBINCLUDELOGS = "yes" # Specifies a location to search for pre-generated tarballs when fetching # a cvs:// URI. Outcomment this, if you always want to pull directly from CVS. CVS_TARBALL_STASH = "http://www.oesources.org/source/current/" # EDIT THIS FILE and then remove the line below before using! REMOVE_THIS_LINE:="${@oe.fatal('Read the comments in your conf/local.conf')}"