1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
#
# OpenEmbedded local configuration file (sample)
#
# Please visit the Wiki at http://openembedded.org/ for more info.
#
# Be SURE to read these comments and setup your build environment before
# proceeding. Once you have done that, remove the line at the end of this
# file and build away.
# The recommended setup is to create a build directory, such as
# ${HOME}/oe/build/ (you may want to put OE and the packages into your
# ${HOME}/oe/oe/ and ${HOME}/oe/packages/ respectively too). Within your
# build environment, you should copy this file into conf/local.conf, and
# then EDIT IT. Fixup any paths to point to the correct locations, and
# setup the target specifications appropriately.
# NOTE: Do NOT use ~ in your paths, OE does NOT expand ~ for you. If you
# must have paths relative to your homedir use ${HOME} (note the {}'s there
# you MUST have them for the variable expansion to be done by OE). Your
# paths should all be absolute paths (They should all start with a / after
# expansion. Stuff like starting with ${HOME} or ${TOPDIR} is ok).
# Once you have done that, you will want to cd into your build environment
# (${HOME}/oe/build/ in this example), then run "oemake targets..." This
# will build into ${TMPDIR} which defaults to ${TOPDIR}/tmp (${TOPDIR} is
# the current directory when oemake was executed).
#
# Quick example of the described stuff above (builds the busybox packages):
#
# mkdir $HOME/sources
# mkdir $HOME/oe
# .. clone oe and packages into $HOME/oe/oe and $HOME/oe/packages ..
# mkdir $HOME/oe/build-arm
# mkdir $HOME/oe/build-arm/conf
# cd $HOME/oe/build-arm
# cp ../packages/conf/local.conf.sample conf/local.conf
# .. EDIT conf/local.conf to set OEFILES and other vars properly ..
# oemake busybox
# .. busybox is built in tmp/ from the current dir ($HOME/oe/build-arm) ..
#
# Use this to specify where OE should place the downloaded sources into
DL_DIR = "${HOME}/sources"
# Delete the line below. Then specify which .oe files to consider for
# your build. Typically this will be something like OEFILES = "/path/to/packages/*/*.oe"
OEFILES := "${@oe.fatal('Edit your conf/local.conf: OEFILES')}"
# Use the OEMASK below to instruct OE to _NOT_ consider some .oe files
# This is a regulary expression, so be sure to get your parenthesis balanced.
OEMASK = ""
# Uncomment this if you want to use a prebuilt toolchain. You will need to
# provide packages for toolchain and additional libraries yourself. You also
# have to set PATH in your environment to make sure OE finds additional binaries.
# Note: You will definitely need to say:
# ASSUME_PROVIDED = "virtual/arm-linux-gcc-2.95"
# to build any of two Linux 2.4 Embedix kernels,
# i.e. openzaurus-sa-2.4.18 and openzaurus-pxa-2.4.18 - and don't forget
# to rename the binaries as instructed in the Wiki.
# ASSUME_PROVIDED = "virtual/${TARGET_PREFIX}gcc virtual/libc"
# Select between multiple alternative providers, if more than one is eligible.
PREFERRED_PROVIDERS = "virtual/qte:qte-for-opie virtual/libqpe:libqpe-opie"
PREFERRED_PROVIDERS += " virtual/libsdl:libsdl-qpe"
PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}gcc-initial:gcc-cross-initial"
PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}gcc:gcc-cross"
PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}g++:gcc-cross"
# Uncomment this to specify where OE should create its temporary files.
# Note that a full build of everything in OE will take GigaBytes of hard
# disk space, so make sure to free enough space. The default TMPDIR is
# <build directory>/tmp
# TMPDIR = /usr/local/projects/oetmp
# Uncomment this to specify a machine to build for. See the conf directory
# for machines currently known to OpenEmbedded.
# MACHINE = "collie"
# Use this to specify the target architecture. Note that this is only
# needed when building for a machine not known to OpenEmbedded. Better use
# the MACHINE attribute (see above)
# TARGET_ARCH = "arm"
# Use this to specify the target operating system. The default is "linux",
# for a normal linux system with glibc. Set this to "linux-uclibc" if you want
# to build a uclibc based system.
# TARGET_OS = "linux"
# TARGET_OS = "linux-uclibc"
# Uncomment this to select a distribution policy. See the conf directory
# for distributions currently known to OpenEmbedded.
# DISTRO = "familiar"
# Uncomment one of these to build packages during the build process.
# This is done automatically if you set DISTRO (see above)
# INHERIT = "package_ipk"
# INHERIT = "package_tar"
# Uncomment one of these lines to get a rootfs image type other than jffs2
# IMAGE_FSTYPE = "tar"
# IMAGE_FSTYPE = "cramfs"
# Uncomment this to disable the parse cache (not recommended).
# CACHE = ""
# Uncomment this if you want OE to emit debugging output
# OEDEBUG = "yes"
# Uncomment these two if you want OE to build images useful for debugging.
# DEBUG_BUILD = "1"
# INHIBIT_PACKAGE_STRIP = "1"
# Uncomment this if you want OE to emit the log if a build fails.
OEINCLUDELOGS = "yes"
# Specifies a location to search for pre-generated tarballs when fetching
# a cvs:// URI. Uncomment this, if you not want to pull directly from CVS.
# CVS_TARBALL_STASH = "http://www.treke.net/oe/source/"
# EDIT THIS FILE and then remove the line below before using!
REMOVE_THIS_LINE:="${@oe.fatal('Read the comments in your conf/local.conf')}"
|
