diff options
Diffstat (limited to 'meta/recipes-kernel/linux/linux-omap-2.6.29/beagleboard/ehci.patch')
| -rw-r--r-- | meta/recipes-kernel/linux/linux-omap-2.6.29/beagleboard/ehci.patch | 131 |
1 files changed, 131 insertions, 0 deletions
diff --git a/meta/recipes-kernel/linux/linux-omap-2.6.29/beagleboard/ehci.patch b/meta/recipes-kernel/linux/linux-omap-2.6.29/beagleboard/ehci.patch new file mode 100644 index 0000000000..5a8c84471b --- /dev/null +++ b/meta/recipes-kernel/linux/linux-omap-2.6.29/beagleboard/ehci.patch @@ -0,0 +1,131 @@ +Index: git/arch/arm/mach-omap2/board-omap3beagle.c +=================================================================== +--- git.orig/arch/arm/mach-omap2/board-omap3beagle.c ++++ git/arch/arm/mach-omap2/board-omap3beagle.c +@@ -154,6 +154,7 @@ static int beagle_twl_gpio_setup(struct + * power switch and overcurrent detect + */ + ++#if 0 /* TODO: This needs to be modified to not rely on u-boot */ + gpio_request(gpio + 1, "EHCI_nOC"); + gpio_direction_input(gpio + 1); + +@@ -163,7 +164,7 @@ static int beagle_twl_gpio_setup(struct + + /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ + gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; +- ++#endif + return 0; + } + +Index: git/arch/arm/mach-omap2/usb-ehci.c +=================================================================== +--- git.orig/arch/arm/mach-omap2/usb-ehci.c ++++ git/arch/arm/mach-omap2/usb-ehci.c +@@ -147,9 +147,11 @@ static void setup_ehci_io_mux(void) + + void __init usb_ehci_init(void) + { ++#if 0 /* TODO: Setup Pin IO MUX for EHCI - moved this temporarily to U-boot */ + /* Setup Pin IO MUX for EHCI */ + if (cpu_is_omap34xx()) + setup_ehci_io_mux(); ++#endif + + if (platform_device_register(&ehci_device) < 0) { + printk(KERN_ERR "Unable to register HS-USB (EHCI) device\n"); +Index: git/drivers/usb/host/ehci-omap.c +=================================================================== +--- git.orig/drivers/usb/host/ehci-omap.c ++++ git/drivers/usb/host/ehci-omap.c +@@ -48,16 +48,25 @@ + * to get the PHY state machine in working state + */ + #define EXTERNAL_PHY_RESET ++#ifdef CONFIG_MACH_OMAP3_BEAGLE ++#define EXT_PHY_RESET_GPIO_PORT2 (147) ++#else + #define EXT_PHY_RESET_GPIO_PORT1 (57) + #define EXT_PHY_RESET_GPIO_PORT2 (61) ++#endif + #define EXT_PHY_RESET_DELAY (10) + ++#define PHY_STP_PULLUP_ENABLE (0x10) ++#define PHY_STP_PULLUP_DISABLE (0x90) ++ + /* ISSUE2: + * USBHOST supports External charge pump PHYs only + * Use the VBUS from Port1 to power VBUS of Port2 externally + * So use Port2 as the working ULPI port + */ ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + #define VBUS_INTERNAL_CHARGEPUMP_HACK ++#endif + + #endif /* CONFIG_OMAP_EHCI_PHY_MODE */ + +@@ -225,14 +234,43 @@ static int omap_start_ehc(struct platfor + + #ifdef EXTERNAL_PHY_RESET + /* Refer: ISSUE1 */ ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + gpio_request(EXT_PHY_RESET_GPIO_PORT1, "USB1 PHY reset"); + gpio_direction_output(EXT_PHY_RESET_GPIO_PORT1, 0); ++#endif + gpio_request(EXT_PHY_RESET_GPIO_PORT2, "USB2 PHY reset"); + gpio_direction_output(EXT_PHY_RESET_GPIO_PORT2, 0); ++ gpio_set_value(EXT_PHY_RESET_GPIO_PORT2, 0); + /* Hold the PHY in RESET for enough time till DIR is high */ + udelay(EXT_PHY_RESET_DELAY); + #endif + ++ /* ++ * The PHY register 0x7 - Interface Control register is ++ * configured to disable the integrated STP pull-up resistor ++ * used for interface protection. ++ * ++ * May not need to be here. ++ */ ++ omap_writel((0x7 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* interface reg */ ++ (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/* Write */ ++ (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */ ++ (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */ ++ (PHY_STP_PULLUP_DISABLE), ++ EHCI_INSNREG05_ULPI); ++ ++ while (!(omap_readl(EHCI_INSNREG05_ULPI) & (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT))); ++ ++ /* Force PHY to HS */ ++ omap_writel((0x4 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* function ctrl */ ++ (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/* Write */ ++ (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */ ++ (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */ ++ (0x40), ++ EHCI_INSNREG05_ULPI); ++ ++ while (!(omap_readl(EHCI_INSNREG05_ULPI) & (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT))); ++ + /* Configure TLL for 60Mhz clk for ULPI */ + ehci_clocks->usbtll_fck_clk = clk_get(&dev->dev, USBHOST_TLL_FCLK); + if (IS_ERR(ehci_clocks->usbtll_fck_clk)) +@@ -307,7 +345,9 @@ static int omap_start_ehc(struct platfor + * Hold the PHY in RESET for enough time till PHY is settled and ready + */ + udelay(EXT_PHY_RESET_DELAY); ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + gpio_set_value(EXT_PHY_RESET_GPIO_PORT1, 1); ++#endif + gpio_set_value(EXT_PHY_RESET_GPIO_PORT2, 1); + #endif + +@@ -393,7 +433,9 @@ static void omap_stop_ehc(struct platfor + + + #ifdef EXTERNAL_PHY_RESET ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + gpio_free(EXT_PHY_RESET_GPIO_PORT1); ++#endif + gpio_free(EXT_PHY_RESET_GPIO_PORT2); + #endif + |