diff options
Diffstat (limited to 'meta/recipes-kernel/linux/linux-omap2-git/beagleboard/TWL4030-02.patch')
| -rw-r--r-- | meta/recipes-kernel/linux/linux-omap2-git/beagleboard/TWL4030-02.patch | 71 |
1 files changed, 71 insertions, 0 deletions
diff --git a/meta/recipes-kernel/linux/linux-omap2-git/beagleboard/TWL4030-02.patch b/meta/recipes-kernel/linux/linux-omap2-git/beagleboard/TWL4030-02.patch new file mode 100644 index 0000000000..48a59b945b --- /dev/null +++ b/meta/recipes-kernel/linux/linux-omap2-git/beagleboard/TWL4030-02.patch @@ -0,0 +1,71 @@ +TWL4030: clear TWL GPIO interrupt status registers + +From: Paul Walmsley <paul@pwsan.com> + +twl_init_irq() does not clear the TWL GPIO ISR registers, but the PIH +ISR thinks that it has. This causes any previously-latched GPIO interrupts +to be stuck on until twl4030-gpio.c initializes, often drowning the console in + + TWL4030 module irq 368 is disabled but can't be masked! + +messages. This seems to be a particular problem when booting on Beagle. + +Signed-off-by: Paul Walmsley <paul@pwsan.com> +--- + + drivers/i2c/chips/twl4030-core.c | 42 ++++++++++++++++++++++++++++++++++++++ + 1 files changed, 42 insertions(+), 0 deletions(-) + +diff --git a/drivers/i2c/chips/twl4030-core.c b/drivers/i2c/chips/twl4030-core.c +index ff662bc..dfc3805 100644 +--- a/drivers/i2c/chips/twl4030-core.c ++++ b/drivers/i2c/chips/twl4030-core.c +@@ -857,6 +857,48 @@ static void twl_init_irq(void) + return; + } + ++ /* GPIO_ISR1A */ ++ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x19); ++ if (res < 0) { ++ pr_err("%s[%d][%d]\n", msg, res, __LINE__); ++ return; ++ } ++ ++ /* GPIO_ISR2A */ ++ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x1a); ++ if (res < 0) { ++ pr_err("%s[%d][%d]\n", msg, res, __LINE__); ++ return; ++ } ++ ++ /* GPIO_ISR3A */ ++ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x1b); ++ if (res < 0) { ++ pr_err("%s[%d][%d]\n", msg, res, __LINE__); ++ return; ++ } ++ ++ /* GPIO_ISR1B */ ++ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x1f); ++ if (res < 0) { ++ pr_err("%s[%d][%d]\n", msg, res, __LINE__); ++ return; ++ } ++ ++ /* GPIO_ISR2B */ ++ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x20); ++ if (res < 0) { ++ pr_err("%s[%d][%d]\n", msg, res, __LINE__); ++ return; ++ } ++ ++ /* GPIO_ISR3B */ ++ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x21); ++ if (res < 0) { ++ pr_err("%s[%d][%d]\n", msg, res, __LINE__); ++ return; ++ } ++ + /* install an irq handler for each of the PIH modules */ + for (i = TWL4030_IRQ_BASE; i < TWL4030_IRQ_END; i++) { + set_irq_chip(i, &twl4030_irq_chip); |