#
# OpenEmbedded local configuration file (sample)
#
# Please visit the Wiki at http://openembedded.org/ for more info.
#

# Be SURE to read these comments and setup your build environment before
# proceeding.  Once you have done that, remove the line at the end of this
# file and build away.

# The recommended setup is to create a build directory, such as
# ${HOME}/oe/build/ (you may want to put OE and the packages into your
# ${HOME}/oe/oe/ and ${HOME}/oe/packages/ respectively too).  Within your
# build environment, you should copy this file into conf/local.conf, and
# then EDIT IT.  Fixup any paths to point to the correct locations, and
# setup the target specifications appropriately.

# NOTE: Do NOT use ~ in your paths, OE does NOT expand ~ for you.  If you
# must have paths relative to your homedir use ${HOME} (note the {}'s there
# you MUST have them for the variable expansion to be done by OE).  Your
# paths should all be absolute paths (They should all start with a / after
# expansion.  Stuff like starting with ${HOME} or ${TOPDIR} is ok).

# Once you have done that, you will want to cd into your build environment
# (${HOME}/oe/build/ in this example), then run "oemake targets..."  This
# will build into ${TMPDIR} which defaults to ${TOPDIR}/tmp (${TOPDIR} is
# the current directory when oemake was executed).

#
# Quick example of the described stuff above (builds the busybox packages):
#
# mkdir $HOME/sources
# mkdir $HOME/oe
#  .. clone oe and packages into $HOME/oe/oe and $HOME/oe/packages ..
# mkdir $HOME/oe/build-arm
# mkdir $HOME/oe/build-arm/conf
# cd $HOME/oe/build-arm
# cp ../packages/conf/local.conf.sample conf/local.conf
#  .. EDIT conf/local.conf to set OEFILES and other vars properly ..
# oemake busybox
#  .. busybox is built in tmp/ from the current dir ($HOME/oe/build-arm) ..
#

# Use this to specify where OE should place the downloaded sources into
DL_DIR = "${HOME}/sources"

# Delete the line below. Then specify which .oe files to consider for
# your build. Typically this will be something like OEFILES = "/path/to/packages/*/*.oe"
OEFILES := "${@oe.fatal('Edit your conf/local.conf: OEFILES')}"

# Use the OEMASK below to instruct OE to _NOT_ consider some .oe files
# This is a regulary expression, so be sure to get your parenthesis balanced.
OEMASK = ""

# Uncomment this if you want to use a prebuilt toolchain. You will need to
# provide packages for toolchain and additional libraries yourself. You also
# have to set PATH in your environment to make sure OE finds additional binaries.
# Note: You will definitely need to say:
#     ASSUME_PROVIDED = "virtual/arm-linux-gcc-2.95"
# to build any of two Linux 2.4 Embedix kernels,
# i.e. openzaurus-sa-2.4.18 and openzaurus-pxa-2.4.18 - and don't forget
# to rename the binaries as instructed in the Wiki.
# ASSUME_PROVIDED = "virtual/${TARGET_PREFIX}gcc virtual/libc"

# Select between multiple alternative providers, if more than one is eligible.
PREFERRED_PROVIDERS = "virtual/qte:qte-for-opie virtual/libqpe:libqpe-opie"
PREFERRED_PROVIDERS += " virtual/libsdl:libsdl-qpe"
PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}gcc-initial:gcc-cross-initial"
PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}gcc:gcc-cross"
PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}g++:gcc-cross"

# Uncomment this to specify where OE should create its temporary files.
# Note that a full build of everything in OE will take GigaBytes of hard
# disk space, so make sure to free enough space. The default TMPDIR is
# <build directory>/tmp
# TMPDIR = /usr/local/projects/oetmp

# Uncomment this to specify a machine to build for. See the conf directory
# for machines currently known to OpenEmbedded.
# MACHINE = "collie"

# Use this to specify the target architecture. Note that this is only
# needed when building for a machine not known to OpenEmbedded. Better use
# the MACHINE attribute (see above)
# TARGET_ARCH = "arm"

# Use this to specify the target operating system.  The default is "linux",
# for a normal linux system with glibc. Set this to "linux-uclibc" if you want
# to build a uclibc based system.
# TARGET_OS = "linux"
# TARGET_OS = "linux-uclibc"

# Uncomment this to select a distribution policy. See the conf directory
# for distributions currently known to OpenEmbedded.
# DISTRO = "familiar"

# Uncomment one of these to build packages during the build process.
# This is done automatically if you set DISTRO (see above)
# INHERIT = "package_ipk"
# INHERIT = "package_tar"

# Uncomment one of these lines to get a rootfs image type other than jffs2
# IMAGE_FSTYPE = "tar"
# IMAGE_FSTYPE = "cramfs"

# Uncomment this to disable the parse cache (not recommended).
# CACHE = ""

# Uncomment this if you want OE to emit debugging output
# OEDEBUG = "yes"

# Uncomment these two if you want OE to build images useful for debugging.
# DEBUG_BUILD = "1"
# INHIBIT_PACKAGE_STRIP = "1"

# Uncomment this if you want OE to emit the log if a build fails.
OEINCLUDELOGS = "yes"

# Specifies a location to search for pre-generated tarballs when fetching
# a cvs:// URI.  Uncomment this, if you not want to pull directly from CVS.
# CVS_TARBALL_STASH = "http://www.treke.net/oe/source/"

# EDIT THIS FILE and then remove the line below before using!
REMOVE_THIS_LINE:="${@oe.fatal('Read the comments in your conf/local.conf')}"